.HA_VERSION

@@ -1 +1 @@
-2023.11.1
+2023.11.0

esphome/riden-labornetzteil.yaml

@@ -1,505 +0,0 @@
-substitutions:
-  name: "riden-labornetzteil"
-  friendly_name: "Riden Labornetzteil"
-  # Change this model to fit your particular one.
-  # You can find it in Home Assistant as the device diagnostic "Model Name".
-  model: "RD6018"
-  device_name: "rd6018-controller"
-  device_friendly_name: "Riden RD6018"
-  device_description: "Labornetzteil"
-  time_timezone: "Europe/Berlin"
-  
-  # Model specific settings (Don't change these!)
-  RD6006_voltage_maximum: "60"
-  RD6006_voltage_accuracy: "2"
-  RD6006_voltage_multiplier: "0.01"
-  RD6006_current_maximum: "6"
-  RD6006_current_accuracy: "3"
-  RD6006_current_multiplier: "0.001"
-  
-  RD6006P_voltage_maximum: "60"
-  RD6006P_voltage_accuracy: "3"
-  RD6006P_voltage_multiplier: "0.001"
-  RD6006P_current_maximum: "6"
-  RD6006P_current_accuracy: "4"
-  RD6006P_current_multiplier: "0.0001"
-
-  RD6012_voltage_maximum: "60"
-  RD6012_voltage_accuracy: "2"
-  RD6012_voltage_multiplier: "0.01"
-  RD6012_current_maximum: "12"
-  RD6012_current_accuracy: "2"
-  RD6012_current_multiplier: "0.01"
-
-  RD6018_voltage_maximum: "60"
-  RD6018_voltage_accuracy: "2"
-  RD6018_voltage_multiplier: "0.01"
-  RD6018_current_maximum: "18"
-  RD6018_current_accuracy: "2"
-  RD6018_current_multiplier: "0.01"
-
-esphome:
-  name: $device_name
-  friendly_name: $device_friendly_name
-  comment: $device_description
-  name_add_mac_suffix: false
-  project:
-    name: "wildekek.rd6006-controller"
-    version: "1.4.1"
-
-esp8266:
-  board: esp12e
-
-wifi:
-  ssid: "Voltage-legacy"
-  password: !secret voltage_legacy_psk
-  use_address: riden-labornetzteil.home  
-  power_save_mode: high
-  fast_connect: on
-
-  # Enable fallback hotspot (captive portal) in case wifi connection fails
-  ap:
-    ssid: "RD6018 Fallback Hotspot"
-    password: !secret fallback_psk
-
-captive_portal:
-
-# Enable logging
-logger:
-  level: INFO
-  # Disable logging via UART, since we're using this for modbus communication
-  baud_rate: 0
-
-# Enable Home Assistant API
-api:
-  encryption: 
-    key: !secret apikey
-
-ota:
-  password: !secret ota
-
-# Enable status LED
-status_led:
-    pin:
-      number: GPIO2
-      inverted: true
-
-uart:
-  id: mod_bus
-  tx_pin: GPIO1
-  rx_pin: GPIO3
-  baud_rate: 115200
-  data_bits: 8
-  stop_bits: 1
-  parity: none
-
-modbus:
- id: modbus1
-
-modbus_controller:
-  - id: powersupply
-    ## This address should be set to the "Address" value in the config menu
-    address: 0x01
-    modbus_id: modbus1
-    setup_priority: -10
-    update_interval: 5s
-
-time:
-  # Get the time from HA, so we can use it for uptime
-  - platform: homeassistant
-    id: time_homeassistant
-    timezone: "${time_timezone}"
-    on_time_sync:
-      - logger.log: Time has been set and is valid!
-      - component.update: sensor_uptime_timestamp
-      - number.set:
-          id: date_year
-          value: !lambda return id(time_homeassistant).now().year;
-      - number.set:
-          id: date_month
-          value: !lambda return id(time_homeassistant).now().month;
-      - number.set:
-          id: date_day
-          value: !lambda return id(time_homeassistant).now().day_of_month;
-      - number.set:
-          id: date_hour
-          value: !lambda return id(time_homeassistant).now().hour;
-      - number.set:
-          id: date_minute
-          value: !lambda return id(time_homeassistant).now().minute;
-      - number.set:
-          id: date_second
-          value: !lambda return id(time_homeassistant).now().second;
-
-sensor:
-  - platform: modbus_controller
-    id: model_number
-    name: "Model Number"
-    entity_category: diagnostic
-    disabled_by_default: True
-    modbus_controller_id: powersupply
-    address: 0
-    skip_updates: 10
-    unit_of_measurement: ""
-    register_type: holding
-    value_type: U_WORD
-    accuracy_decimals: 0
-    on_value:
-      then:
-        - lambda: |-
-            id(model_name).publish_state(value_accuracy_to_string(x, 0));
-
-  - platform: modbus_controller
-    name: "Serial Number"
-    entity_category: diagnostic
-    disabled_by_default: True
-    modbus_controller_id: powersupply
-    address: 1
-    skip_updates: 10
-    register_type: holding
-    value_type: U_DWORD
-    accuracy_decimals: 0
-  
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 3
-    name: "Firmware version"
-    entity_category: diagnostic
-    disabled_by_default: True
-    unit_of_measurement: ""
-    register_type: holding
-    value_type: U_WORD
-    accuracy_decimals: 2
-    filters:
-      - multiply: 0.01
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 10
-    name: "Output voltage"
-    device_class: voltage
-    state_class: measurement
-    unit_of_measurement: "V"
-    register_type: holding
-    value_type: U_WORD
-    accuracy_decimals: ${${model}_voltage_accuracy}
-    filters:
-      - multiply: ${${model}_voltage_multiplier}
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 11
-    name: "Output current"
-    device_class: current
-    state_class: measurement
-    unit_of_measurement: "A"
-    register_type: holding
-    value_type: U_WORD
-    accuracy_decimals: ${${model}_current_accuracy}
-    filters:
-      - multiply: ${${model}_current_multiplier}
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 12
-    name: "Output Power"
-    device_class: power
-    state_class: measurement
-    unit_of_measurement: "W"
-    register_type: holding
-    value_type: U_DWORD
-    accuracy_decimals: 2
-    filters:
-      - multiply: 0.01
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 33
-    name: "Battery voltage"
-    device_class: voltage
-    state_class: measurement
-    unit_of_measurement: "V"
-    register_type: holding
-    value_type: U_WORD
-    accuracy_decimals: ${${model}_voltage_accuracy}
-    filters:
-      - multiply: ${${model}_voltage_multiplier}
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 38
-    name: "Battery charge"
-    device_class: "energy_storage"
-    state_class: measurement
-    unit_of_measurement: "Ah"
-    icon: "mdi:battery-60"
-    register_type: holding
-    value_type: U_DWORD
-    accuracy_decimals: 3
-    filters:
-      - multiply: 0.001
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 40
-    name: "Battery energy"
-    device_class: "energy_storage"
-    state_class: measurement
-    unit_of_measurement: "Wh"
-    icon: "mdi:battery-60"
-    register_type: holding
-    value_type: U_DWORD
-    accuracy_decimals: 3
-    filters:
-      - multiply: 0.001
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 14
-    name: "Input voltage"
-    device_class: voltage
-    unit_of_measurement: "V"
-    register_type: holding
-    value_type: U_WORD
-    accuracy_decimals: ${${model}_voltage_accuracy}
-    filters:
-      - multiply: ${${model}_voltage_multiplier}
-  
-  - platform: modbus_controller
-    name: "Temperature"
-    device_class: temperature
-    state_class: measurement
-    modbus_controller_id: powersupply
-    register_type: holding
-    address: 4
-    value_type: S_DWORD
-    unit_of_measurement: "°C"
-    
-  - platform: modbus_controller
-    name: "Temperature external"
-    state_class: measurement
-    modbus_controller_id: powersupply
-    register_type: holding
-    address: 34
-    value_type: S_DWORD
-    device_class: temperature
-    unit_of_measurement: "°C"
-    
-  - platform: wifi_signal
-    name: "Wi-Fi Signal"
-    disabled_by_default: True
-    update_interval: 60s
-
-  # Uptime is used internally only
-  - platform: uptime
-    id: sensor_uptime
-  # This sensor is an alternative for the uptime sensor, which only sends the
-  # startup timestamp of the device to home assistant once
-  - platform: template
-    id: sensor_uptime_timestamp
-    name: "Uptime"
-    entity_category: diagnostic
-    device_class: "timestamp"
-    accuracy_decimals: 0
-    update_interval: never
-    lambda: |-
-      static float timestamp = (
-        id(time_homeassistant).utcnow().timestamp - id(sensor_uptime).state
-      );
-      return timestamp;
-
-text_sensor:
-  - platform: wifi_info
-    ip_address:
-      name: "IP Address"
-      disabled_by_default: True
-    ssid:
-      name: "Wi-Fi SSID"
-      disabled_by_default: True
-    bssid:
-      name: "Wi-Fi BSSID"
-      disabled_by_default: True
-  - platform: template
-    id: model_name
-    name: "Model Name"
-    entity_category: diagnostic
-    # Updated by model number
-    update_interval: never
-    filters:
-      - map:
-        - 60062 -> RD6006
-        - 60065 -> RD6006P
-        - 60121 -> RD6012
-        - 60181 -> RD6018
-
-binary_sensor:
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Keypad lock"
-    entity_category: diagnostic
-    device_class: lock
-    address: 15
-    register_type: holding
-    bitmask: 0x1
-    filters:
-      - invert:
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    address: 32
-    name: "Battery mode"
-    device_class: connectivity
-    register_type: holding
-    bitmask: 0x1
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Over Voltage Protection"
-    device_class: problem
-    address: 16
-    register_type: holding
-    bitmask: 0x1
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Over Current Protection"
-    device_class: problem
-    address: 16
-    register_type: holding
-    bitmask: 0x2
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Constant Voltage"
-    address: 17
-    register_type: holding
-    bitmask: 0x1
-    filters:
-      - invert:
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Constant Current"
-    address: 17
-    register_type: holding
-    bitmask: 0x1
-
-number:
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Backlight"
-    icon: "mdi:lightbulb"
-    entity_category: config
-    address: 72
-    value_type: U_WORD
-    min_value: 0
-    max_value: 5
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Output voltage"
-    device_class: voltage
-    unit_of_measurement: "V"
-    entity_category: config
-    address: 8
-    value_type: U_WORD
-    min_value: 0
-    max_value: ${${model}_voltage_maximum}
-    step: ${${model}_voltage_multiplier}
-    lambda: !lambda return x * ${${model}_voltage_multiplier};
-    write_lambda: !lambda return x * (1/${${model}_voltage_multiplier});
-  
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Output current"
-    device_class: current
-    unit_of_measurement: "A"
-    entity_category: config
-    address: 9
-    value_type: U_WORD
-    min_value: 0
-    max_value: ${${model}_current_maximum}
-    step: ${${model}_current_multiplier}
-    lambda: !lambda return x * ${${model}_current_multiplier};
-    write_lambda: !lambda return x * (1/${${model}_current_multiplier});
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Over Voltage Protection"
-    device_class: voltage
-    unit_of_measurement: "V"
-    address: 82
-    entity_category: config
-    value_type: U_WORD
-    min_value: 0
-    max_value: ${${model}_voltage_maximum}
-    step: ${${model}_voltage_multiplier}
-    lambda: !lambda return x * ${${model}_voltage_multiplier};
-    write_lambda: !lambda return x * (1/${${model}_voltage_multiplier});
-
-
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Over Current Protection"
-    device_class: current
-    unit_of_measurement: "A"
-    address: 83
-    entity_category: config
-    value_type: U_WORD
-    min_value: 0
-    max_value: ${${model}_current_maximum}
-    step: ${${model}_current_multiplier}
-    lambda: !lambda return x * ${${model}_current_multiplier};
-    write_lambda: !lambda return x * (1/${${model}_current_multiplier});
-
-  # Date components are kept internal
-  - platform: modbus_controller
-    id: date_year
-    modbus_controller_id: powersupply
-    entity_category: diagnostic
-    register_type: holding
-    address: 48
-    value_type: U_WORD
-  - platform: modbus_controller
-    id: date_month
-    modbus_controller_id: powersupply
-    entity_category: diagnostic
-    register_type: holding
-    address: 49
-    value_type: U_WORD
-  - platform: modbus_controller
-    id: date_day
-    modbus_controller_id: powersupply
-    entity_category: diagnostic
-    register_type: holding
-    address: 50
-    value_type: U_WORD
-  - platform: modbus_controller
-    id: date_hour
-    modbus_controller_id: powersupply
-    entity_category: diagnostic
-    register_type: holding
-    address: 51
-    value_type: U_WORD
-  - platform: modbus_controller
-    id: date_minute
-    modbus_controller_id: powersupply
-    entity_category: diagnostic
-    register_type: holding
-    address: 52
-    value_type: U_WORD
-  - platform: modbus_controller
-    id: date_second
-    modbus_controller_id: powersupply
-    entity_category: diagnostic
-    register_type: holding
-    address: 53
-    value_type: U_WORD
-
-switch:
-  - platform: modbus_controller
-    modbus_controller_id: powersupply
-    name: "Output"
-    address: 18
-    register_type: holding
-    bitmask: 0x1
-    entity_category: config
-
-button:
-  - platform: safe_mode
-    name: "Safe mode"