automations.yaml

@@ -342,15 +342,11 @@
     to: home
     from: not_home
   condition:
-  - condition: or
-    conditions:
   - condition: sun
-      after: sunset
     before: sunrise
     before_offset: '+1'
+    after: sunset
     after_offset: '-1'
-    - condition: sun
-      before: sunrise
   action:
   - service: script.moodlight_neutral
   - service: light.turn_on

esphome/livingroom.yaml

@@ -1,236 +0,0 @@
-esphome:
-  name: livingroom
-  platform: ESP32
-  board: nodemcu-32s
-  
-  on_boot:
-    then:
-      - light.turn_on:
-          id: co2_light
-          red: 0%
-          green: 100%
-          blue: 9%
-      - delay: 1.5s
-      - light.turn_on:
-          id: co2_light
-          red: 100%
-          green: 75%
-          blue: 0%
-      - delay: 1.5s
-      - light.turn_on:
-          id: co2_light
-          red: 100%
-          green: 0%
-          blue: 0%
-      - delay: 1.5s
-      - light.turn_on:
-          id: co2_light
-          red: 100%
-          green: 75%
-          blue: 0%
-      - delay: 1.5s
-      - light.turn_on:
-          id: co2_light
-          red: 0%
-          green: 100%
-          blue: 9%
-      - text_sensor.template.publish:
-          id: co2_warn
-          state: "grün"
-      - text_sensor.template.publish:
-          id: pm25_warn
-          state: "grün"
-
-wifi:
-  ssid: "Voltage-legacy"
-  password: !secret voltage_legacy_psk
-  use_address: livingroom.home  
-  power_save_mode: high
-  fast_connect: on
-
-  # Enable fallback hotspot (captive portal) in case wifi connection fails
-  ap:
-    ssid: "Wohnzimmer Fallback Hotspot"
-    password: !secret fallback_psk
-
-captive_portal:
-
-# Enable logging
-logger:
-  level: DEBUG
-
-# Enable Home Assistant API
-api:
-  password: !secret api
-
-# Enable over-the-air updates
-ota:
-  password: !secret ota
-
-# Initialize I²C
-i2c:
- - id: bus_a
-   sda: 13
-   scl: 16
-   scan: true
-
-# Initialize LEDC GPIOs
-output:
-  - platform: ledc
-    pin: GPIO17
-    id: led_red
-  - platform: ledc
-    pin: GPIO18
-    id: led_green
-    max_power: 50%
-  - platform: ledc
-    pin: GPIO19
-    id: led_blue
-
-# Define RGB mode for LED
-light:
-  - platform: rgb
-    id: co2_light
-    name: "CO2 Status LED"
-    red: led_red
-    green: led_green
-    blue: led_blue
-    internal: true
-
-# Initialize UART for Vindriktning sensor
-uart:
-  rx_pin: GPIO26
-  baud_rate: 9600
-
-# Create text sensor to represent CO2 LED warn state (somewhat redundant)
-text_sensor:
-  - platform: template
-    name: "Wohnzimmer CO2 Warnstufe"
-    id: co2_warn
-  - platform: template
-    name: "Wohnzimmer Feinstaub Warnstufe"
-    id: pm25_warn
-
-sensor:
-  # WiFi signal strength
-  - platform: wifi_signal
-    name: "WiFi Signalstärke"
-    update_interval: 60s
-  # SCD30 CO2 +  temperature + humidity sensor
-  # * air quality category 0: LED is purple, sensor needs calibration (<380ppm)
-  # • air quality category 1: LED is green (380-800ppm) 
-  # • air quality category 2: LED is yellow (900-1200ppm) 
-  # • air quality category 3: LED is orange/amber (1200 to 1600ppm) 
-  # • air quality category 4: LED is red (1600-2000ppm) 
-  - platform: scd30
-    i2c_id: bus_a
-    co2:
-      name: "Wohnzimmer CO2"
-      id: co2_value
-      accuracy_decimals: 1
-      on_value_range:
-        - below: 380
-          then:
-            - text_sensor.template.publish:
-                id: co2_warn
-                state: "Kalibrierung nötig"
-            - light.turn_on:
-                id: co2_light
-                red: 75%
-                green: 0%
-                blue: 100%
-        - above: 380
-          below: 800
-          then:
-            - text_sensor.template.publish:
-                id: co2_warn
-                state: "grün"
-            - light.turn_on:
-                id: co2_light
-                red: 0%
-                green: 100%
-                blue: 0%
-        - above: 800
-          below: 1200
-          then:
-            - text_sensor.template.publish:
-                id: co2_warn
-                state: "gelb"
-            - light.turn_on:
-                id: co2_light
-                red: 100%
-                green: 100%
-                blue: 0%
-        - above: 1200
-          below: 1600
-          then:
-            - text_sensor.template.publish:
-                id: co2_warn
-                state: "orange"
-            - light.turn_on:
-                id: co2_light
-                red: 100%
-                green: 75%
-                blue: 0%
-        - above: 1600
-          then:
-            - text_sensor.template.publish:
-                id: co2_warn
-                state: "rot"
-            - light.turn_on:
-                id: co2_light
-                red: 100%
-                green: 0%
-                blue: 0%
-    temperature:
-      name: "Wohnzimmer Temperatur"
-      accuracy_decimals: 2
-    humidity:
-      name: "Wohnzimmer Luftfeuchtigkeit"
-      accuracy_decimals: 1
-    # SCD30 temp sensor is a bit off
-    temperature_offset: 1.5 °C
-    ambient_pressure_compensation: 1
-    automatic_self_calibration: True
-    address: 0x61
-    update_interval: 60s
-  # Vindriktning particulate matter sensor
-  - platform: pm1006
-    pm_2_5:
-      name: "Wohnzimmer Feinstaub PM 2.5µm"
-      on_value_range:
-      - above: 0
-        below: 35
-        then:
-          - text_sensor.template.publish:
-              id: pm25_warn
-              state: "grün"
-      - above: 35
-        below: 85
-        then:
-          - text_sensor.template.publish:
-              id: pm25_warn
-              state: "orange"
-      - above: 85
-        then:
-          - text_sensor.template.publish:
-              id: pm25_warn
-              state: "rot"
-  # Analog photo diode voltage
-  - platform: adc
-    pin: 32
-    name: "Spannung Photodiode"
-    attenuation: 11db
-    update_interval: 1s
-    internal: true
-    on_value_range:
-      - below: 0.25
-        then:
-          light.turn_on:
-            id: co2_light
-            brightness: 30%
-      - above: 0.4
-        then:
-          light.turn_on:
-            id: co2_light
-            brightness: 60%

esphome/livingroom/partitions.csv

@@ -1,6 +0,0 @@
-nvs,      data, nvs,     0x009000, 0x005000,
-otadata,  data, ota,     0x00e000, 0x002000,
-app0,     app,  ota_0,   0x010000, 0x1C0000,
-app1,     app,  ota_1,   0x1D0000, 0x1C0000,
-eeprom,   data, 0x99,    0x390000, 0x001000,
-spiffs,   data, spiffs,  0x391000, 0x00F000