Introduced the light component.

Adopted rgb_light.
Added brightness based on photodiode voltage.
Added warn levels for particle dust.
Removed actions out of sensors. Will be replaced by actions based on warn lavels.

All values (brightness / colors / voltage) still uncalibrated.

esphome/sleepingroom.yaml

@@ -3,19 +3,19 @@ esphome:
   platform: ESP32
   board: nodemcu-32s
   
-  # Dirty hack, because on_value_range does not trigger green if sensor
-  # value is within green range on boot.
-  on_boot:
-    then:
-      - output.set_level:
-          id: led_green
-          level: 58%
-      - output.set_level:
-          id: led_red
-          level: 0%
-      - text_sensor.template.publish:
-          id: co2_warn
-          state: "grün"
+#  # Dirty hack, because on_value_range does not trigger green if sensor
+#  # value is within green range on boot.
+#  on_boot:
+#    then:
+#      - output.set_level:
+#          id: led_green
+#          level: 58%
+#      - output.set_level:
+#          id: led_red
+#          level: 0%
+#      - text_sensor.template.publish:
+#          id: co2_warn
+#          state: "grün"
 
 wifi:
   ssid: "Voltage-legacy"
@@ -57,10 +57,20 @@ output:
   - platform: ledc
     pin: GPIO18
     id: led_green
+    max_power: 50%
   - platform: ledc
     pin: GPIO19
     id: led_blue
 
+# Example configuration entry
+light:
+  - platform: rgb
+    id: co2_light
+    name: "CO2 Status LED"
+    red: led_red
+    green: led_green
+    blue: led_blue
+
 # Initialize UART for Vindriktning sensor
 uart:
   rx_pin: GPIO26
@@ -71,6 +81,9 @@ text_sensor:
   - platform: template
     name: "Schlafzimmer CO2 Warnstufe"
     id: co2_warn
+  - platform: template
+    name: "Schlafzimmer Feinstaub Warnstufe"
+    id: pm25_warn
 
 sensor:
   # WiFi signal strength
@@ -92,47 +105,23 @@ sensor:
         - above: 380
           below: 800
           then:
-            - output.set_level:
-                id: led_green
-                level: 58%
-            - output.set_level:
-                id: led_red
-                level: 0%
             - text_sensor.template.publish:
                 id: co2_warn
                 state: "grün"
         - above: 800
           below: 1200
           then:
-            - output.set_level:
-                id: led_green
-                level: 58%
-            - output.set_level:
-                id: led_red
-                level: 80%
             - text_sensor.template.publish:
                 id: co2_warn
                 state: "gelb"
         - above: 1200
           below: 1600
           then:
-            - output.set_level:
-                id: led_green
-                level: 50%
-            - output.set_level:
-                id: led_red
-                level: 100%
             - text_sensor.template.publish:
                 id: co2_warn
                 state: "orange"
         - above: 1600
           then:
-            - output.set_level:
-                id: led_green
-                level: 0%
-            - output.set_level:
-                id: led_red
-                level: 100%
             - text_sensor.template.publish:
                 id: co2_warn
                 state: "rot"
@@ -161,6 +150,24 @@ sensor:
   - platform: pm1006
     pm_2_5:
       name: "Feinstaub PM 2.5µm"
+      on_value_range:
+      - above: 0
+        below: 35
+        then:
+          - text_sensor.template.publish:
+              id: pm25_warn
+              state: "grün"
+      - above: 35
+        below: 85
+        then:
+          - text_sensor.template.publish:
+              id: pm25_warn
+              state: "orange"
+      - above: 85
+        then:
+          - text_sensor.template.publish:
+              id: pm25_warn
+              state: "rot"
   # Analog photo diode voltage
   - platform: adc
     pin: 32
@@ -168,6 +175,17 @@ sensor:
     attenuation: 11db
     update_interval: 1s
     internal: true
+    on_value_range:
+      - below: 0.3
+        then:
+          light.turn_on:
+            id: co2_light
+            brightness: 50%
+      - above: 0.3
+        then:
+          light.turn_on:
+            id: co2_light
+            brightness: 100%
 
 # IR Receiver, dumps all received values into serial
 remote_receiver: